首页说明书ISO 10110-4-1997
OptiX

文档

10

关注

0

好评

0
PDF

ISO 10110-4-1997

阅读 727 下载 200 大小 306.77K 总页数 8 页 2023-02-19 分享
价格:免费文档
下载文档
/ 8
全屏查看
ISO 10110-4-1997
还有 8 页未读 ,您可以 继续阅读 或 下载文档
1、本文档共计 8 页,下载后文档不带水印,支持完整阅读内容或进行编辑。
2、当您付费下载文档后,您只拥有了使用权限,并不意味着购买了版权,文档只能用于自身使用,不得用于其他商业用途(如 [转卖]进行直接盈利或[编辑后售卖]进行间接盈利)。
3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。
4、如文档内容存在违规,或者侵犯商业秘密、侵犯著作权等,请点击“违规举报”。
INTERNATIONALSTANDARD10110-4First edition1997-08-01Optics and optical instruments-Preparation of drawings for opticalelements and systems一Part 4:Material imperfections-Inhomogeneity andstriaeOptique et instruments d'optique-Indications sur les dessins pourelements et systemes optiques-Partie 4:Imperfections des materiaux-Heterogeneite et striesThis material is reproduced from ISO documents under InternationalOrganization for Standardization (ISO)Copyright License numberIHS/ICC/1996.Not for resale.No part of these ISO documents may bereproduced in any form,electronic retrieval system or otherwise,except asallowed in the copyright law of the country of use,or with the prior writtenconsent of ISO(Case postale 56,1211 Geneva 20,Switzerland,Fax +41 22734 10 79),IHS or the ISO Licensor's members.Reference number1S010110-4:1997(E)1s010110-4:1997(E)ForewordISO (the Intemational Organization for Standardization)is a worldwidefederation of national standards bodies (ISO member bodies).The work ofpreparing International Standards is normally carried out through ISOtechnical committees.Each member body interested in a subject for whicha technical committee has been established has the right to be representedon that committee.Intemational organizations,governmental and non-governmental,in liaison with ISO,also take part in the work.ISOcollaborates closely with the Intemational Electrotechnical Commission(IEC)on all matters of electrotechnical standardization.Draft International Standards adopted by the technical committees arecirculated to the member bodies for voting.Publication as an InternationalStandard requires approval by at least 75%of the member bodies castinga vote.Standard ISO 10110-4 was prepared by TechnicalCommittee ISO/TC 172,Optics and optical instruments,SubcommitteeSC 1,Fundamental standards.ISO 10110 consists of the following parts,under the general title Opticsand optical instruments-Preparation of drawings for optical elements andsystems.Part 1:GeneralPart 2:Material imperfections-Stress birefringencePart 3:Material imperfections-Bubbles and inclusionsPart 4:Materlal Imperfections-Inhomogeneity and striaePart 5:Surface form tolerancesPart 6:Centring tolerancesPart 7:Surface imperfection tolerancesPart 8:Surface textureAll rights reserved.Unless otherwise specified,no part of this publication may be reproducedor utilized in any form or by any means,electronic or mechanical,including photocopying andmicrofilm,without permission in writing from the publisher.International Organization for StandardizationCase postale 56.CH-1211 Geneve 20.SwitzerlandX.400c=ch;a=400net;p=iso;o=isocs;s=centralPrinted in Switzerland1S010110-4:1997(E)Part 9:Surface treatment and coatingPart 10:Table representing data of a lens elementPart 11:Non-toleranced data-Part 12:Aspheric surfaces一Part 13:Laser irradiation damage thresholdAnnex A of this part of ISO 10110 is for information only.光
文档评分
    请如实的对该文档进行评分
  • 0
发表评论
返回顶部